ASTM A192/A192M Standard Specification for Seamless Carbon Steel Boiler Tubes for High-Pressure Service.ASTM A192/A192M高压用无缝碳钢锅炉管标准规范。

ASTM A192/A192M guide covers standard specifications for minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, and silicon. The tubes shall have a hardness number not exceeding a specific value. The following mechanical tests shall be conducted, namely: flattening test; flaring test; hardness test; and hydrostatic test.

ASTM A192/A192M指南涵盖了高压用无缝碳钢锅炉和过热器管的最小壁厚标准规范。钢应符合碳、锰、磷、硫和硅所需的化学成分。管子的硬度值不得超过特定值。应进行以下机械试验，即：平整试验；燃烧试验；硬度试验；水压试验。

What is ASTM A192? ASTM A192是什么？

ASTM A192 is a standard for seamless carbon steel boiler and superheater tubes with minimum wall thickness for high-pressure applications. The standard is issued under the fixed designation A 192/A 192M. It is under the jurisdiction of ASTM Committee A01 on Steel. 

ASTM A192是高压应用中最小壁厚的无缝碳钢锅炉和过热器管的标准。该标准以固定名称A 192/A 192M发布。它由ASTM钢委员会A01管辖。

ASTM A192 is generally used for high-pressure boilers with a working pressure that does not exceed 9.8Mpa. The tubes are available in hot rolled and cold drawn delivery states. 

ASTM A192通常用于工作压力不超过9.8Mpa的高压锅炉。这些管子有热轧和冷拔两种交付状态。

ASTM A192 Seamless Steel Tube ASTM A192无缝钢管

ASTM A192 Seamless Steel Tube is applied as minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. 

ASTM A192无缝钢管作为最小壁厚，用于高压服务的无缝碳钢锅炉和过热器管。

Scope范围

1. 1. This specification2 covers minimum-wall-thickness, seamless carbon steel boiler and superheater tubes for high-pressure service. 
   2. 1.1本规范涵盖了高压用无缝碳钢锅炉和过热器管的最小壁厚。

1.2 The tubing sizes and thicknesses usually furnished to this specification are 1/2 in. to 7 in. [12.7 to 177.8 mm] outside diameter and 0.085 to 1.000 in. [2.2 to 25.4 mm], inclusive, in minimum wall thickness. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification. 

1.2本规范中通常提供的管材尺寸和厚度为外径1/2英寸至7英寸[12.7至177.8毫米]，最小壁厚为0.085至1.000英寸[2.2至25.4毫米]。可以提供具有其他尺寸的管子，前提是这些管子符合本规范的所有其他要求。

1.3 Mechanical property requirements do not apply to tubing smaller than 1/8 in. [3.2 mm] inside diameter or 0.015 in. [0.4 mm] thickness. 

1.3机械性能要求不适用于内径小于1/8英寸[3.2毫米]或厚度小于0.015英寸[0.4毫米]的管子。

1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. 

1.4以英寸-磅单位或国际单位表示的值应单独视为标准值。在文本中，国际单位制显示在括号中。每个系统中所述的值不是完全等效的；因此，每个系统都必须独立使用。将两个系统的值结合起来可能会导致不符合规范。除非订单中指定了本规范的“M”名称，否则应采用英寸-磅单位。

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

1.5本国际标准是根据世界贸易组织技术性贸易壁垒委员会发布的《关于制定国际标准、指南和建议的原则的决定》中确立的国际公认的标准化原则制定的。

What is the chemical composition of ASTM A192?  ASTM A192的化学成分是什么？

ASTM A192/A192M Mechanical Properties  ASTM A192/A192M机械性能

What is the yield strength of ASTM A192?  ASTM A192的屈服强度是多少？

The tensile strength and yield strength of the ASTM A192/ ASME SA-192 tube are 325 MPa and 180 MPa at room temperature, respectively. 

ASTM A192/ASME SA-192管在室温下的抗拉强度和屈服强度分别为325 MPa和180 MPa。

*T.S.: tensile strength; *Y.S.: yield strength; *El.: elongation. 

TS.：抗拉强度*Y.S.：屈服强度*El：伸长。
*The Brinell Hardness number applies to ASTM A192 tubes 0.200″ [5.1 mm] and over in wall thickness.

布氏硬度值适用于壁厚为0.200英寸[5.1毫米]及以上的ASTM A192管。
*The Rockwell Hardness number applies to ASTM A192 tubes less than 0.200″ [5.1 mm] in wall thickness.

洛氏硬度值适用于壁厚小于0.200英寸[5.1毫米]的ASTM A192管。
*Mechanical properties don’t apply to tubing smaller than 1/8″ [3.2 mm] inside diameter or 0.015″ [0.4 mm] thickness.

*机械性能不适用于内径小于1/8英寸[3.2毫米]或厚度小于0.015英寸[0.4毫米]的管子。

ASTM A192/A192M Mechanical Tests Required    ASTM A192/A192M要求的机械试验

Flattening test, flaring test, hardness test, hydrostatic test, and tension test.  压扁试验、扩口试验、硬度试验、水压试验和拉伸试验。

Carbon Steel ASTM A192 / ASME SA192 Tubes Equivalent Grades  ASTM A192/ASME SA192碳钢管等效格栅

ASTM A 192 boiler tube equivalent EN 10216-2, DIN 17175, BS 3059 Part II, NF A 49-213, NBR 5594 ASTM (American Society for Testing Materials standard) A192 and ASME (American Society of Mechanical Engineers standards) SA192. Equivalent Materials 1010, St35.8, 360. FASTWELL has standard specifications for minimum-wall-thickness, seamless carbon steel boiler and super heater tubes for high-pressure service.

ASTM A 192锅炉管相当于EN 10216-2、DIN 17175、BS 3059第二部分、NF A 49-213、NBR 5594 ASTM（美国材料试验学会标准）A192和ASME（美国机械工程师学会标准）SA192。等效材料1010，St35.8360。FASTWELL具有最小壁厚、无缝碳钢锅炉和高压过热器管的标准规格。

ASTM A192/A192M Pressure Rating ASTM A192/A192M压力等级

Maximum working pressure of ASTM A192 Tube at temperature 400°F, The dimensions - outside pipe diameters and wall thicknesses are according ANSI B36.10.

ASTM A192管材在400°F温度下的最大工作压力，尺寸——外径和壁厚符合ANSI B36.10。

What is SA 192 equivalent to? SA 192等于什么？

The ASTM A192/ASME SA192 standard is applicable to seamless carbon steel pipes used for boilers and superheaters in high-pressure environments, with a focus on meeting the minimum wall thickness necessary for these applications.

ASTM A192/ASME SA192标准适用于高压环境中用于锅炉和过热器的无缝碳钢管，重点是满足这些应用所需的最小壁厚。

ASTM A 192 boiler tube equivalent EN 10216-2, DIN 17175, BS 3059 Part II, NF A 49-213, NBR 5594 ASTM (American Society for Testing Materials standard) A192 and ASME (American Society of Mechanical Engineers standards) SA192. Equivalent Materials 1010, St35.

ASTM A 192锅炉管相当于EN 10216-2、DIN 17175、BS 3059第二部分、NF A 49-213、NBR 5594 ASTM（美国材料试验学会标准）A192和ASME（美国机械工程师学会标准）SA192。等效材料1010，St35。

American Standard A192/SA192 Seamless Carbon Steel Boiler and Superheater Tubes for High Pressure Minimum Wall Thicknesses 

美国标准A192/SA192高压用无缝碳钢锅炉和过热器管最小壁厚

ASTM A192/A192M - Industries & Applications    ASTM A192/A192M-工业和应用

Our ASTM A192/A192M are widely used in various industries due to their excellent properties and performance. Some of the key industries and applications where ASTM A192 tubes find extensive use include:

我们的ASTM A192/A192M因其优异的性能和性能而广泛应用于各个行业。ASTM A192管材广泛使用的一些关键行业和应用包括：

• Gas Processing Industries 天然气加工行业
• Petrochemical Industries石化行业
• Power Generation Industries发电行业
• Food Processing Industries食品加工业
• Chemical Industries化学工业
• Oil & Gas Industries石油和天然气行业
• Fertilizers Industries化肥行业
• Sugar Industries糖业